Ciscoの642-883認定試験はIT業界の中でとても普遍的な試験になります。試験の準備は時間とエネルギーがかかります。時は金なり社会に時間を無駄しないようによいツルを探し出されるのはみんなの希望です。IT-Passports.comのCiscoの642-883認証試験の問題集は君の20時間だけかかりますよ。
弊社が提供した問題集がほかのインターネットに比べて問題のカーバ範囲がもっと広くて対応性が強い長所があります。IT-Passports.comが持つべきなIT問題集を提供するサイトでございます。
ずっと自分自身を向上させたいあなたは、642-883認定試験を受験する予定があるのですか。もし受験したいなら、試験の準備をどのようにするつもりですか。もしかして、自分に相応しい試験参考書を見つけたのでしょうか。では、どんな参考書は選べる価値を持っていますか。あなたが選んだのは、IT-Passports.comの642-883問題集ですか。もしそうだったら、もう試験に合格できないなどのことを心配する必要がないのです。
Cisco 642-883認証試験を通るために、いいツールが必要です。Cisco 642-883認証試験について研究の資料がもっとも大部分になって、IT-Passports.comは早くてCisco 642-883認証試験の資料を集めることができます。弊社の専門家は経験が豊富で、研究した問題集がもっとも真題と近づいて現場試験のうろたえることを避けます。
試験番号：642-883問題集
試験科目：Cisco 「Deploying Cisco Service Provider Network Routing (SPROUTE) 」
問題と解答：全82問
あなたはIT-Passports.comが提供したCiscoの642-883認定試験の問題集だけ利用して合格することが問題になりません。ほかの人を超えて業界の中で最大の昇進の機会を得ます。もしあなたはIT-Passports.comの商品がショッピング車に入れて24のインターネットオンライン顧客サービスを提供いたします。問題があったら気軽にお問いください、
購入前にお試し,私たちの試験の質問と回答のいずれかの無料サンプルをダウンロード：http://www.it-passports.com/642-883.html
NO.1 When troubleshooting OSPF neighbor errors, which three verification steps should be considered.?
(Choose three.)
A. Verify if neighboring OSPF interfaces are configured in the same area.
B. Verify if neighboring OSPF interfaces are configured with the same OSPF process ID.
C. Verify if neighboring OSPF interfaces are configured with the same OSPF priority.
D. Verify if neighboring OSPF interfaces are configured with the same hello and dead intervals.
E. Verify if neighboring OSPF interfaces are configured with the same area type.
Answer: A,D,E
Cisco認定証 642-883問題集 642-883練習問題 642-883認定証 642-883過去問 642-883
NO.2 Which four statements are correct regarding IS-IS operations? (Choose four.)
A. By default, Level 1 routers within an IS-IS area do not carry any routing information external to the area
to which they belong. They use a default route to exit the area.
B. Summarization should be configured on the Level 2 routers, which injects the Level 2 routes into Level
1.
C. IS-IS supports "route leaking" in which selected Level 2 routes can be advertised by a Level 1/Level 2
router into Level 1.
D. The IS-IS backbone is a contiguous collection of Level 1 capable routers, each of which can be in a
different area.
E. With IS-IS, an individual router is in only one area, and the border between areas is on the link that
connects two routers that are in different areas.
F. Cisco IOS XR Software supports multitopology for IPv6 IS-IS unless single topology is explicitly
configured in IPv6 address-family configuration mode.
Answer: A,C,E,F
Cisco 642-883認定資格 642-883
NO.3 When configuring IPv4 and IPv6 IS-IS routing on Cisco IOS XR routers, which three statements are
correct? (Choose three.)
A. By default, a single SPF is used for both IPv4 and IPv6, so the IPv4 and IPv6 topology should be the
same.
B. By default, the IS-IS router type is Level 1 and Level 2.
C. All IS-IS routers within the same IS-IS area must be configured with the same IS-IS routing process
instance ID.
D. By default, metric-style narrow is used.
E. By default, the IS-IS interface circuit type is Level 1 and Level 2.
F. The area IS-IS address-family configuration command is used to specify the IS-IS area address.
Answer: B,D,E
Cisco問題集 642-883認証試験 642-883認定証 642-883認証試験 642-883
NO.4 In comparing IS-IS with OSPF, a Level-1-2 IS-IS router is similar to which kind of OSPF router?
A. ASBR on a normal OSPF area
B. ASBR on NSSA
C. ABR on totally stubby OSPF area
D. ABR on stubby OSPF area
E. ABR on a normal OSPF area
Answer: C
Cisco認定試験 642-883 642-883問題集 642-883問題集
NO.5 Refer to the PE1 router routing table output exhibit.
What is causing the i su 10.1.10.0/24 [115/30] via 0.0.0.0, 00:40:34, Null0 entry on the PE1 router routing
table?
A. The PE1 router is receiving the 10.1.10.0/24 summary route from the upstream L1/L2 IS-IS router.
B. The PE1 router has been configured to summarize the 10.1.10.x/32 IS-IS routes to 10.1.10.0/24.
C. The 10.1.10.0/24 has been suppressed because IS-IS auto-summary has been disabled on the PE1
router.
D. The 10.1.10.0/24 has been suppressed because of a route policy configuration on the PE1 router.
E. The 10.1.10.0/24 has been suppressed because the more specific 10.1.10.x/32 IS-IS routes have
been configured to leak into the IS-IS non-backbone area.
Answer: B
Cisco 642-883問題集 642-883参考書 642-883認定証
NO.6 On Cisco IOS XR Software, which set of commands is used to enable the gi0/0/0/1 interface for OSPF
in area 0?
A. interface gi0/0/0/0 ip address 10.1.1.1 255.255.255.0 ! router ospf 1 network 10.1.1.1 0.0.0.0 area 0
B. interface gi0/0/0/0 ip address 10.1.1.1 255.255.255.0 ! router ospf 1 network 10.1.1.1 255.255.255.255
area 0
C. router ospf 1 area 0 interface GigabitEthernet0/0/0/1
D. interface gi0/0/0/0 ip address 10.1.1.1 255.255.255.0 ip ospf 1 area 0
E. router ospf 1 address-family ipv4 unicast interface GigabitEthernet0/0/0/1 area 0
F. router ospf 1 address-family ipv4 unicast interface GigabitEthernet0/0/0/1 area 0
Answer: C
Cisco 642-883過去問 642-883練習問題 642-883練習問題
NO.7 Which three statements are true regarding the OSPF router ID? (Choose three.)
A. The OSPF routing process chooses a router ID for itself when it starts up.
B. The router-id command is the preferred procedure to set the router ID.
C. If a loopback interface is configured, its address will always be preferred as the router ID over any
other methods.
D. After the router ID is set, it does not change, even if the interface that the router is using for the router
ID goes down. The router ID changes only if the router reloads or if the OSPF routing process restarts.
E. In OSPF version 3, the OSPF router ID uses a 128-bit number.
Answer: A,B,D
Cisco認定試験 642-883練習問題 642-883
NO.8 What is function of the RP/0/RSP0/CPU0:PE1(config-ospf)#distance Cisco IOS-XR command?
A. To modify the administrative distance of the OSPF routes
B. To modify the default seed metric of the OSPF external routes
C. To modify the OSPF default reference bandwidth
D. To modify the OSPF cost
Answer: A
Cisco 642-883認定資格 642-883 642-883参考書 642-883
NO.9 Refer to the OSPF command exhibit.
Which effect does the no-summary command option have?
A. It will cause area 1 to be able to receive non-summarized inter-area routes.
B. It will cause area 1 to not receive any inter-area routes and will use a default route to reach networks in
other areas.
C. It will cause area 1 to not receive any external routes and will use a default route to reach the external
networks.
D. It will convert the NSSA area into a NSSA totally stubby area.
E. It will convert the stubby area into a NSSA.
F. It will disable OSPF auto-summary.
Answer: B
Cisco 642-883問題集 642-883 642-883 642-883問題集
NO.10 Which two OSPF network scenarios require OSPF virtual link configuration? (Choose two.)
A. to connect an OSPF non-backbone area to area 0 through another non-backbone area
B. to connect an NSSA area to an external routing domain
C. to connect two parts of a partitioned backbone area through a non-backbone area
D. to enable route leaking from Level 2 into Level 1
E. to enable route leaking from Level 1 into Level 2
F. to enable OSPF traffic engineering
Answer: A,C
Cisco認定証 642-883 642-883認定試験 642-883問題集
みなさんにIT-Passports.comを選ぶのはより安心させるためにIT-Passports.comは部分のCisco 642-883試験材料がネットで提供して、君が無料でダウンロードすることができます。安心に弊社の商品を選ぶとともに貴重な時間とエネルギーを節約することができる。IT-Passports.comは真実のCisco 642-883認証試験の問題集が100%で君の試験の合格を保証します。君の明るい将来を祈っています。
没有评论:
发表评论